EdgeHalf Struct Reference

Public Attributes
EdgeHalf *	next
EdgeHalf *	prev
BMEdge *	e
BMFace *	fprev
BMFace *	fnext
BoundVert *	leftv
BoundVert *	rightv
int	profile_index
int	seg
float	offset_l
float	offset_r
float	offset_l_spec
float	offset_r_spec
bool	is_bev
bool	is_rev
bool	is_seam
bool	visited_rpo
char	_pad [4]

Detailed Description

Definition at line 86 of file bmesh_bevel.cc.

Member Data Documentation

_pad

char EdgeHalf::_pad[4]

Definition at line 119 of file bmesh_bevel.cc.

e

BMEdge* EdgeHalf::e

Original mesh edge.

Definition at line 90 of file bmesh_bevel.cc.

Referenced by adjust_miter_coords(), adjust_the_cycle_or_chain(), bevel_build_rings(), bevel_edge_order_extend(), bevel_vert_construct(), bevel_vert_two_edges(), edges_angle_kind(), fast_bevel_edge_order(), find_bevel_edge_order(), find_edge_half(), geometry_collide_offset(), next_edgehalf_bev(), offset_meet(), offset_meet_edge(), offset_meet_lines_percent_or_absolute(), offset_on_edge_between(), pipe_test(), point_between_edges(), square_out_adj_vmesh(), and vertex_collide_offset().

fnext

BMFace* EdgeHalf::fnext

Face between this edge and next, if any.

Definition at line 94 of file bmesh_bevel.cc.

Referenced by bevel_build_edge_polygons(), bevel_vert_construct(), edges_angle_kind(), frep_for_center_poly(), geometry_collide_offset(), offset_meet(), and offset_meet_lines_percent_or_absolute().

fprev

BMFace* EdgeHalf::fprev

Face between this edge and previous, if any.

Definition at line 92 of file bmesh_bevel.cc.

Referenced by bevel_build_edge_polygons(), bevel_vert_construct(), edges_angle_kind(), find_bevel_edge_order(), frep_for_center_poly(), offset_meet(), and offset_meet_lines_percent_or_absolute().

is_bev

bool EdgeHalf::is_bev

Is this edge beveled?

Definition at line 112 of file bmesh_bevel.cc.

Referenced by bevvert_is_weld_cross(), build_boundary(), check_edge_data_seam_sharp_edges(), frep_for_center_poly(), geometry_collide_offset(), next_edgehalf_bev(), offset_on_edge_between(), and regularize_profile_orientation().

is_rev

bool EdgeHalf::is_rev

Is e->v2 the vertex at this end?

Definition at line 114 of file bmesh_bevel.cc.

Referenced by geometry_collide_offset().

is_seam

bool EdgeHalf::is_seam

Is e a seam for custom loop-data (e.g., UVs).

Definition at line 116 of file bmesh_bevel.cc.

Referenced by bevel_build_edge_polygons(), and bevel_build_rings().

leftv

BoundVert* EdgeHalf::leftv

Left boundary vert (looking along edge to end).

Definition at line 96 of file bmesh_bevel.cc.

Referenced by adjust_offsets(), bev_rebuild_polygon(), bevel_build_edge_polygons(), build_boundary(), build_boundary_terminal_edge(), and regularize_profile_orientation().

next

EdgeHalf* EdgeHalf::next

Other EdgeHalves connected to the same BevVert, in CCW order.

Definition at line 88 of file bmesh_bevel.cc.

Referenced by build_boundary(), check_edge_data_seam_sharp_edges(), geometry_collide_offset(), next_edgehalf_bev(), and offset_meet().

offset_l

float EdgeHalf::offset_l

Offset for this edge, on left side.

Definition at line 104 of file bmesh_bevel.cc.

Referenced by adjust_the_cycle_or_chain(), bevel_limit_offset(), offset_meet(), offset_meet_edge(), and tri_corner_test().

offset_l_spec

float EdgeHalf::offset_l_spec

User specification for offset_l.

Definition at line 108 of file bmesh_bevel.cc.

Referenced by bevel_limit_offset(), build_boundary_terminal_edge(), geometry_collide_offset(), and vertex_collide_offset().

offset_r

float EdgeHalf::offset_r

Offset for this edge, on right side.

Definition at line 106 of file bmesh_bevel.cc.

Referenced by adjust_the_cycle_or_chain(), bevel_limit_offset(), offset_meet(), offset_meet_edge(), and offset_on_edge_between().

offset_r_spec

float EdgeHalf::offset_r_spec

User specification for offset_r.

Definition at line 110 of file bmesh_bevel.cc.

Referenced by bevel_limit_offset(), and geometry_collide_offset().

prev

EdgeHalf * EdgeHalf::prev

Definition at line 88 of file bmesh_bevel.cc.

Referenced by bev_rebuild_polygon(), geometry_collide_offset(), and offset_meet().

profile_index

int EdgeHalf::profile_index

Offset into profile to attach non-beveled edge.

Definition at line 100 of file bmesh_bevel.cc.

Referenced by bev_rebuild_polygon().

rightv

BoundVert* EdgeHalf::rightv

Right boundary vert, if beveled.

Definition at line 98 of file bmesh_bevel.cc.

Referenced by adjust_miter_coords(), adjust_offsets(), bev_rebuild_polygon(), bevel_build_edge_polygons(), build_boundary_terminal_edge(), and regularize_profile_orientation().

seg

int EdgeHalf::seg

How many segments for the bevel.

Definition at line 102 of file bmesh_bevel.cc.

Referenced by bevel_build_edge_polygons(), bevel_build_poly(), and build_boundary().

visited_rpo

bool EdgeHalf::visited_rpo

Used during the custom profile orientation pass.

Definition at line 118 of file bmesh_bevel.cc.

Referenced by regularize_profile_orientation().

---

The documentation for this struct was generated from the following file:

• bmesh_bevel.cc